Products Categories

AAC EN 50182 DIN 48201 All-aluminum Conductor

Execution standard: BS EN 50182 (Old Standard: DIN 48201)

Material: AAC adopts AL1 aluminum material.

Product application:Lightweight by design, AAC conductors simplify transportation, handling, and installation, reducing labor costs and speeding up project timelines, especially in complex terrains.

AAC is an all-aluminum conductor designed for balanced performance in electrical transmission. Its pure aluminum makeup ensures strong conductivity, while its lightweight nature eases handling and installation. It’s particularly suitable for medium-voltage lines in areas with moderate weather, delivering consistent power flow with economic efficiency.

Product advantage

They are commonly employed in overhead power lines for rural electrification projects, where their lightweight design and cost-effectiveness make them ideal for extending power access to remote villages and agricultural regions.

AAC Standard: EN 50182 (Old Standard: DIN 48201)

Type: AL1

Aluminum Stranded Conductor(AAC)
Code Name	Old Code Name	Sectional Area	Wire Diameter&Stranding		Overall Diameter	Nominal Breaking Load	Linear Mass	Maximum Resistance at 20℃	Modulus of elasticity	Coefficient of linear expansion	Current-carrying capacity
Code Name	Old Code Name	mm2	mm	No.	mm	kN	kg/km	Ω/km	N/MM2	1/K	A
16-AL1	16	15.9	1.7	7	5.1	3.02	43.5	1.7986	60000	2.3x10-5	110
24-AL1	25	24.2	2.1	7	6.3	4.36	66.4	1.1787	60000	2.3x10-5	145
34-AL1	35	34.4	2.5	7	7.5	6.01	94.1	0.8317	60000	2.3x10-5	180
49-AL1	50	49.5	3	7	9	8.41	135.5	0.5776	60000	2.3x10-5	225
48-AL1	50	48.3	1.8	19	9	8.94	133.0	0.5944	57000	2.3x10-5	225
66-AL1	70	65.8	2.1	19	10.5	11.85	181.1	0.4367	57000	2.3x10-5	270
93-AL1	95	93.3	2.5	19	12.5	16.32	256.6	0.3081	57000	2.3x10-5	340
117-AL1	120	117.0	2.8	19	14	19.89	321.9	0.2456	57000	2.3x10-5	390
147-AL1	150	147.1	2.25	37	15.75	26.48	405.8	0.1960	57000	2.3x10-5	455
182-AL1	185	181.6	2.5	37	17.5	31.78	500.9	0.1588	57000	2.3x10-5	520
243-AL1	240	242.5	2.25	61	20.25	43.66	669.9	0.1193	55000	2.3x10-5	625
299-AL1	300	299.4	2.5	61	22.5	52.40	827.0	0.0966	55000	2.3x10-5	710
400-AL1	400	400.1	2.89	61	26.01	68.02	1105.2	0.0723	55000	2.3x10-5	855
500-AL1	500	499.8	3.23	61	29.07	82.47	1380.5	0.0579	55000	2.3x10-5	990
626-AL1	625	626.2	2.96	91	32.56	106.45	1730.5	0.0464	55000	2.3x10-5	1140
802-AL1	800	802.1	3.35	91	36.85	132.34	2216.6	0.0362	55000	2.3x10-5	1340
1000-AL1	1000	999.7	3.74	91	41.14	159.95	2762.8	0.0291	55000	2.3x10-5	1540

Note:

1.The outermost layer is twisted to the right (Z).

2. The elastic coefficients and expansion coefficients listed in this table are applicable to Germany. The calculation of other conductor structure parameters shall refer to IEC61597.

3. The flow rate values listed in this table are applicable under the conditions of a frequency of 60HZ, a wind speed of 0.6m/S, sunlight exposure in Germany, an ambient temperature of 35℃, and a conductor temperature of 80℃. In case of special laying conditions, the flow rate values should be reduced if there is no convection Less than 30%.

AAC EN 50182 DIN 48201 All-aluminum Conductor

Product advantage

AAC Standard: EN 50182 (Old Standard: DIN 48201)

Leave Your Message

PVC Covered Conductor (BS 6485)

Neutral-Supported Power Cable Assemblieswith Weather-Resistant Extruded Insulationrated 600 Volts (Icea-S-76-474)

AAAC BS EN 50182 BS3242 All Aluminum Alloy Conductor

AAAC ASTM B399 All Aluminum Alloy Conductor

0.6/1kv Aerial Bundled Conductor Systems(Executive Standard: NF C33-209)

AAAC EN 50182 DIN 48201 All Aluminum Alloy Conductor